下载中心  |   网站地图  |   站内搜索  |   加入收藏
*新更新
业界动态
产品信息
安恒动态
技术文章


安恒公司 / 技术文章 / 布线测试与布线标准 / IntelliTone Pro实战--布线音频探测技术应用分析与布线管理
IntelliTone Pro实战--布线音频探测技术应用分析与布线管理
2006-06-15    安恒公司整理       阅读:
Cable Toning Techniques Using IntelliTone Toners and Probes

Moves, adds and changes for datacom and telecom networks

IntelliTone is a digital toning system optimized for toning into modern network equipment and Category 5 cabling. To achieve this, IntelliTone uses radio frequencies and a digital tone packet that drives all 4 pairs with a variety of toning methods.

Datacom network moves, adds and changes using IntelliTone Pro Toners and Probes
In recent years, installation of structured cable has been to uniform standards. The TIA-568A standard requires that all work areas be wired with a minimum of two jacks with the horizontal cabling being four-pair 100 ohm UTP. This typically consists of 2 or more Cat5e cable runs directly from a wall plate jack to a patch panel.

Plugging in
IntelliTone is a digital toning system featuring an 8-position modular jack. This allows the toner to be plugged in either at the wall jack with the included patch cable or, if the wall jack is obstructed but connected, the patch cable can be removed from the PC and plugged directly into the toner.

Wall jacks are often unmarked or misconnected. Adding to the confusion, the 8-position modular jack can be used for either data or telecom services.

Service ID provides the first clue
The IntelliTone Pro 200 Toner features a service ID indicating the presence of service on the line. When plugged in to a wall jack, it provides the first indication of where to look for the cable in the closet. A 4-position jack is sure to be telecom service, whereas an 8-position jack could be telecom or data (network) connection. The presence of telecom service typically means looking for the signal on a 110 block with an active connection to the phone system.


The presence of Ethernet indicates the connection is active and best located on the patch cables from the patch panel to the switch. If the connection is open then it likely not patched or connected. If the open LED is extinguished, the toner is detecting a connection across the center pins of the jack. This could be an un-plugged network device or unrecognized service.

Locating in the closet

The tone can be located on un-patched connections by moving the probe from jack to jack on the patch panel. It is typical to get a reading of 4-6 in locate mode with the black probe tip inserted into the jack. Neighboring jacks and cable will exhibit lower signal levels as indicated by the LED display.


If the service identification in the office indicated an Ethernet connection, the user should begin probing the cables that are patched to active network equipment. It is typical to get a reading of 7-8 on the toned cable.


Once the cable is located, the IntelliTone Pro 200 probe provides a Cablemap to assure correct pin-to-pin wiring. By removing the patch cable from the switch, or by plugging a patch cable into the patch panel jack, the complete end-to-end wiring can be verified for opens, shorts, or mis-wires.

When in tight spaces or in the presence of bleed, the isolate position will help eliminate bleed and provide more granularity on the stronger LEDs. This will aid in differentiating the toned cable or jack from its neighbors by providing a couple of LED levels of difference in strength. Additionally Cablemap always provides a definitive indication of the toned cable.

 

Toning from the closet to office jack
Occasionally toning may be performed from the patch panel to the office jack. If the jacks are very closely spaced or it is difficult to insert the probe tip in the jack, there may only be one or two levels of signal strength difference. If more differentiation is required for extremely close jacks, a short patch cable can be used to effectively distance the jacks by probing the cable as it is moved from jack to jack. The same patch cable can then be used to validate the correct cable using the Cablemap feature on the IntelliTone Pro 200 probe.


Telecom moves, adds, changes using IntelliTone
Most office installations consist of a one or more data and telephone drops. On the telecom side, there can be a variety of jacks and wiring schemes ranging from a single pair on a 4-position wall jack to 4 pairs connected from the 8 position modular jack to the terminating block.

Wiring Schemes
In the office, the wall plate jack may be 6 or 8-postion, with the 6-position jack having 4 or 6 pins. Horizontal cabling uses 1, 2, 3, or 4 pairs and can range from Category 3 to Category 5 cable. In the closet, the horizontal cabling will typically terminate on a 110 block, or in older sites a 66 block. The block may be directly connected to the PBX if this is the main distribution frame (MDF), or cross-connected to another location if this is an intermediate distribution frame (IDF). Current practice, per TIA-568A standard, consists of an 8-position jack in the office with 4-pair 100 ohm UTP connected to a 110 block.

Plugging into a jack
The IntelliTone toner features an 8-position modular jack that accepts 4, 6 or 8 position male plugs. The included 4 and 8 position patch cables allow the toner to be plugged into the wall jack.

If the wall jack is obstructed but connected, the patch cable can be disconnected at the phone, and the male plug, be it 4, 6 or 8 position can be connected directly to the toner female jack.

 

Plugging in to a 66 or 110 block
There are a variety of ways to connect the toner to the pair. The supplied alligator test leads makes bare wire attachment possible. For piercing wires, Fluke Networks offers the MT-8203-20, a telecom 5-way Alligator Lead Set with a bed of nails.
The telecom 5-way Alligator Lead Set also offers a secure attachment to 66 blocks using the U shaped nose for blade shaped terminals. It is also possible to use a 66 quick clip and connect to the toner using the 8-position modular plug.

For 110 blocks, a standard 1-pair 110 to modular plug patch cable can be plugged directly into the toner modular jack. There are also various 110 test adapters that provide a modular jack for connection to the toner.

 

Isolate Individual Wire Pairs
The IntelliTone digital signal is subject to significant bleed-over between pairs in a cable. This is especially true for Cat 3 cabling. Because of this, IntelliTone’s analog mode is recommended for isolating individual pairs. The SmartTone™ analog mode should be used because of its ability to change cadence when the pair under test is shorted. When the pair under test is not terminated, the copper conductors can be touched together briefly to cause a short. When this happens, the tone will change its cadence to indicate that the correct pair has been located. If the pair is terminated on a 66 or 110 block, it may be necessary to short the pair together with a pair of insulated pliers.

In the distribution frame
In the closet, the telecom jack will typically terminate on a 110 block. The block may be directly connected to the PBX if this is the MDF, or cross-connected another location if this is an IDF. More recent installations, per the TIA-568 standard, consist of an RJ-45 jack in the office with all 4 pairs punched down on the 110 block. Locate the cable by touching wire with the tip, either the insulation or by making metalic contact.

Once located, the office wiring can be verified for shorts, opens and mis-wires using a standard 110 to 8-position patch cable and the Cablemap feature on the IntelliTone Pro 200 probe. The cables are readily available in 1, 2 and 4-pair 110 connection in TIA-568A, TIA-568B or Universal Service Ordering Code (USOC) formats. The Cablemap results will show the correct order when the patch cable matches the wiring scheme, be it TIA-568A, TIA-586B and USOC.

The IntelliTone Pro probe supports the time-honored practice of making contact with the finger. While often done on 66 blocks, it is possible to make the contact with the 110 connections using a metallic object. Using the body to conduct the signal is a good way to move the probe away from noise sources and identify individual wires when metallic contact is possible.

 

Locating Cables on an Active PBX System
Some PBX lines generate signals in the operating frequency of IntelliTone as seen by the SYNC LED flashing red. In this case, it may be difficult for IntelliTone to differentiate the PBX signal from the IntelliTone signal. Once again, it is recommended to use IntelliTone’s analog mode for this application. Make sure that both the IntelliTone Toner and the IntelliTone Probe are in analog mode.

Moves, adds, changes completion
When returning to the office to retrieve the toner, the presence of the correct services on the correct jacks can quickly be verified using the IntelliTone 200 toner Service ID feature. The verification of the correct patching and connection, including datacom or telecom services, can be performed prior to the computer or phone being present.

https://anheng.com.cn/news/html/cabling_test/Cable_Toning_Techniques_Using_IntelliTone_Toners_and_Probes.html 

责任编辑: admin

相关文章
IntelliTone Pro专业型数字查线仪(ITT)  10-05-09 - 阅: 208994
网络诊断日记(十):使用智能数字查线仪(IntelliTone)定位线缆  10-01-10 - 阅: 189011
安恒签订IntelliTone Pro和LinkRunner的NMPP产品的大订单  07-11-29 - 阅: 290305
IntelliTone Pro集成数字和模拟音频发生器工作原理  06-07-13 - 阅: 269475
模拟音频 PK 数字音频, 布线测试音频定位技术比较  05-11-29 - 阅: 276082
融合数字音频和TDR技术加快LAN环境中的电缆定位和故障诊断  05-07-30 - 阅: 256637
IntelliTone网络数字音频和探头技术帮助您即时查看网络中的移动、增加及改变, 链路定位与标识  04-09-27 - 阅: 262041
Fluke IntelliTone 智能数字查线仪获得 IDG产品年度奖  04-09-15 - 阅: 257987
EIA/TIA-606标准简介《商业及建筑物电信基础结构的管理标准》,布线管理布线标准  04-08-25 - 阅: 287068
安恒公司全面推广布线系统管理与维护整体方案,布线管理  04-07-21 - 阅: 423316
用户对布线管理与维护的声音  04-07-01 - 阅: 232113
网络测试应用技术:定位网络线缆——布线管理与维护  04-04-06 - 阅: 227661
Fluke 发布IntelliTone智能数字查线仪  04-02-18 - 阅: 253285
相关产品
福禄克Fluke 2042电缆探测仪音频探测故障定位  05-11-10 - 阅: 863311
AirMagnet Wi-Fi Analyzer 无线网络探测工具 便携式无线网分析仪(AirMagnet LapTop)--无线局域网分析仪  05-08-29 - 阅: 1497564
无线网络探测工具 掌上型无线网分析仪Handheld WLT 7.0  05-08-16 - 阅: 2137388
无线网络探测工具 无线局域网勘测仪Surveyor-无线网信号覆盖与分析工具  05-08-03 - 阅: 1879295
F140音频探测器Tone probe布线管理维护基础工具  03-08-24 - 阅: 1540165
LinkWare 电缆测试管理软件,布线管理  03-02-25 - 阅: 1580195
IntelliTone智能数字查线仪Fluke数字式音频探测器MT-8200-60A  04-09-02 - 阅: 1752845

Email给朋友 打印本文
版权所有·安恒公司 Copyright © 2004   simplifiber.anheng.com.cn   All Rights Reserved    
      北京市海淀区*体南路9号 主语国际商务中心4号楼8层 安恒公司(邮编100048) 电话:010-88018877